Proizvodi

Disano 3273 Stelvio 1 – Plus S – LED


Tehnički opisi:
PDF: technicalsheet


Housing and cover: in die-cast aluminium and designed with a very small surface exposed to wind. Cooling fins are integrated into the cover.
Pole connection: in die-cast aluminium and with gaskets to secure the frame according to different inclinations. Adjustable ranges: between 0° and 15° for side mount; and between 0° and 10° for mast-top mounting. Inclination pace: 5°. Suited for poles with a diameter 63-60mm
Diffuser: clear, tempered glass, 4 mm thick, resistant to thermal shock and impacts (UNI-EN 12150-1 : 2001)
Coating: the standard powder coating consists of a first metal surface pre-treatment stage and of single layer of UV-stabilised, corrosion and salt resistant polyester powder coating.

Show more...

Standard supply: Automatic temperature control inside the device with automatic resetting.  Electronic safety device to protect the LED module and the related ballast compliant with EN 61547.
It works in two modes:
– differential mode: surge between power cables and between the phase and neutral.
– common mode: surge between power, L/N and ground cables or between the fixture’s body if it is of class II and installed on a metal pole.
Upon request: protection up to 10KV.
Equipment: complete with IP67 airtight connector for mains connection. Supplied with double insulation switch that cuts off electricity when the cover is opened.
Energy-saving: the possibility to choose the correct drive current for LEDs will allow you to have the right power under specific design conditions, and also help you deal with maintenance and retrofitting problems. Using a lower current will improve the efficiency of fixtures and therefore increase energy savings, whilst a higher current will result in a higher light flux so that you can reduce the number of fixtures.
Optics: V0 polycarbonate with micro-faceted finish. Flow recovery in V2 polycarbonate.
The total return of the equipment is close to 100%LED: Latest generation LED technology, Ta-30+40°C life 80%: >100.000h (L80B10).
Photobiological safety class: exempt group EN62471.
Power factor >0.9
Regulations:Produced according to applicable EN60598-1 CEI 34-21 standards, degree of protection according to EN 60529 standards.
Upon request:
– with power supply 1-10 V dimmable with subcode 12.
– with power supply DIG dimmable with subcode 0041.
– with virtual midnight subcode 30.
– power line carrier remote control systems subcode 0078.
Wind surface: L:229cm² F:470cm².

Show less...

 


CodeGearKgLumen Output-K-CRIWTotColour
330344-00CLD CELL10.2LED 8646lm-700mA-4000K-CRI>7076W6/8kV
330345-00CLD CELL11.2LED 13138lm-700mA-4000K-CRI>70114W6/8kV
330347-00CLD CELL12.2LED 17517lm-700mA-4000K-CRI>70152W6/8kV
330344-30CLD CELL10.44LED 8646lm-700mA-4000K-CRI>7076W6/8kV
330345-30CLD CELL10.3LED 13138lm-700mA-4000K-CRI>70114W6/8kV
330347-30CLD CELL11.74LED 17517lm-700mA-4000K-CRI>70152W6/8kV
330344-39CLD CELL9.8LED 8041lm-700mA-3000K-CRI>7074W6/8kV
330345-39CLD CELL11.2LED 12218lm-700mA-3000K-CRI>70114W6/8kV
330347-39CLD CELL10.84LED 16291lm-700mA-3000K-CRI>70148W6/8kV

 

KONTAKTIRAJTE NAS:

     

    Kategorija: